Done a modification to your Logans? How about a room treatment? Share tweaks to your system here!
Hello everyone, I went through the process of Cleaning my Martin Logan Quest Stators in the shower. I wrote the process down and created a PDF for everyone. Hope this helps those interested in doing the same. Cheers
i would just like to share and help any one who has a low out put from there panel ,or any one who wants to coat there speakers with conductive liquid what you do is with a a sharp knife cut away the glue top and bottom sticky stuff be very careful. when it is open clean the panels with distiled...
Hello, So the material covering the Motion series grills started to bother me, I felt it wasn't 100% acoustically transparent. The Motion FX is easier to modify, removal of the grill and cloth is simply and you don't need any tools. The fabric used in both of these not only doesn't pass light...
A Logos center with a Summit panel : summos center. In combination with an active subwoofer (don't need a big one ) , 2 way filtering of the panel and you have the perfect center ! Something smaller ,use then the Stylos panel ,is the same size as the Logos Update: I have finish now the center,...
I have a few ML speakers. My CLS2's were changed to CLS2a config. some time ago with the ML (in field) circuit changes and I intended at some stage to do the CLS2z conversion. I got most of the parts I needed, including Mundorf Supreme Film caps ( a bundle to make up the 50 mF equiv.) and Erse...
I have the schematic for this crossover but cant figure out if its a 2nd or 1st order x-over. Anybody have an idea? Thinking it was a 2nd order and looking up the transfer functions of 2nd order hi pass filters I figured I needed to add 200 uf to the 39 uf in there. Is this right? I should add...
These are made of glass with a cork top which have some anti static properties. I read that by elevating speaker cables off the floor you eliminate static charge and you lower capacitance. The net effect is lower noise and increased dynamics What's your thoughts? :cool:
Panel support pillar reinforcement: Custom-made granite pieces, 1/2 inch thick, 6lbs each, attached to the speaker with thin sorbothane sheet; shifts and absorbs audible resonances out of operating range. I used #10 1-1/4 inch self-tapping screws (impossible to find in black in any small quantity)....
So I've been unhappy with the Summit X for a variety of reasons, I can't fit the CLX in my room, and I really like the O's... which led me here, exploring the possibility of upgrading the O's crossover, of this very worthy speaker. This is a continuation of this thread... the comments from other...
Posted by zanash on February 25, 2003 at 23:52:39: Tweaks for Aerius i mkII "...Just change the link between the hi and lo freq. speaker terminals, for a small length of your fave speaker cable. Alternatively make a suitable link from flattened copper pipe, cut and shape using a dremel type tool....
Firstly i must say hi to all ML owners, i registered years ago when i bought my first pair,(Vantages), but clearly messed up my login as i never could get in. I re registered as i would like to share my latest project with my Spires. Essentially, i decided to re-house all of the electronics in a...
I decided that the -3dB switch on the Odysseys isn't cutting it, so I set out to attenuate the bass, which ultimately affects the midrange as well. Below is a picture of the prototype showing two 50W resistors (aluminum cased, wire-wound thus inductive) in series totaling 4 ohms. The final version...
Tom will probably move this to Tweaks, but I am posting it here since this gets more traffic than the other pages. I am still experimenting/tweaking my Spires after 9 months as these are the first Logan's I have owned and keep learning about them and how to set them up. Little changes can make...
Hello all, I have seen a few threads on this model and mods , they were all old so I wanted to seer if anyone can help me . I want to change the caps and coils I dont know what voltage caps I need to get . I have seen a few people that bypass the caps and I am not sure which of these...
Jim Power's Toe-in Technique Sent in by Ken Henegar - as told to him by Jim Power of ML. Posted on March 13, 2003 My technique for ideal toe-in is pretty low tech but extremely accurate. Get a flashlight. Sit in the listening seat. Hold the flashlight directly above the top of your head....
Not sure why, but I was not all that impressed with the jumpers that came with my Vista's. Looking around, I found, like anything else in audio, you can go nuts with jumpers.. $500 for jumpers, uh, no. Given my positive experience with Anti Cables, I decided to order their jumpers. Cheap &...
Following the suggestions of Rabbit and some of the other members, I've recently embarked on an experiment of adding mass dampers to my speakers and componenet. Rather than just balancing lead bars or steel plates, or buying store-bought tweaks, I've decided to try some "off-the-shelf" solutions. ...
I have modified my Ascents' crossovers using Obbligato Gold caps several weeks ago. I changed caps only and did not touch the inductors. The results were very good, and the last bit of the modification came today: a polypropylene replacement for the bipolar electrolitycs. It's Jantzen...
This mod will give a more open and dynamic sound to the Monolith III, the electrolytic 100uf cap C2A should be changed for a good quality polyproplene of the same value, at least 150volt or more voltage rating, you might find it hard to get 100uf so you can parralel say 2x40 and 1x20 to get the...
Dear Tom, would you leave this post in the main discussion forum for a little while? Since you're from Madison, I'll cut you some slack. :o I've re-directed to the Tweaks forum with a 3 month re-direct. - Tom. Tim has documented the following most important mods for the clsIIz speaker. ...
Hello everyone :) This is one of my first posts on this great forum. I'm going to tell you a little about the upgrades I have done on my Ascent I speakers. First thing I would like to make clear, I am not a audio engineer nor do I proclaim to have an audiophile golden ear. I am simply someone...
Use this control to limit the display of threads to those newer than the specified time frame.
Allows you to choose the data by which the thread list will be sorted.
Order threads in...
Note: when sorting by date, 'descending order' will show the newest results first.
Forum Rules
