Please allow me after all the years since the last comment on this thread, to reopen the topic Synergistic Research HFT´s.
I for myself who live in Germany didn´t hear about the HFT´s before a month ago.
I have purchased 3 packs and installed them according to Synergistic Research description...
Hi Tosh,
Thank you very much for your advise, much appreciated. I will follow your recommendation and live with the slightly fat/muddy bass as it only concerns some recordings (CDs).
I am already driving the Aerius in vertical passive bi-amping and my special confected speaker cables (Kimber...
Hi and wish you All a marry Christmas,
Despite not having received any comments to my tweet above I did the re-capping around 4 years ago as described. I am very happy with the result.
I also have re-foiled panels since app 3 years.
Now I would like to ask you for another possible tweak to...
Thank you Tosh,
My Aerius is not an "i" but I suppose it does not matter. The Scanspeak is available here in Germany.
Ist it a 1:1 swap or do I need to modify anything on the Cross Over?
Thank you slightly for your advice.
Would you be kind enough to give me the exact Vifa type?
I will document it for the day I decide to change them. Until now they do a grate job, I am satisfied :)
Nice tweed, does anyone of you know which bass speaker unit sound better, Vifa or Eminence?
My Aerius still have the Vifas and until now they are fine but just want to prepare myself for the day they need changing.
Are the Vifas and the Eminence 1:1 interchangeable?
No one out there that has experience with the room lenses?
I do know that the Argent lenses are not available anymore but I was hoping that some of you made the clones and would share your experience either with the originals or the clones.
Thank you.
Hi,
I can see that this thread is quite old but I will try to ask for your experience with the Argent Room Lenses.
A few weeks ago I built two Jon Risch clones of the former Argent Room Lenses.
The Room Lenses are made from high density thick walled PVC tubes, sitting in a base made of MDF and...
A few weeks ago I built two Jon Risch clones of the former Argent Room Lenses.
The Room Lenses are made from high density thick walled PVC tubes, sitting in a base made of MDF and the tubes are open at both ends, The tubes are stuffed with buffy polyester batting at different specific heights to...
Hi,
Following this interesting thread I have a few questions concerning HV supply on my Aerius (not i)
What is the correct HV Voltage?
Does the Aerius have a self adjusting HV bias circuit?
Does the HV Voltage drop with time (years)?
My Aerius lacks a bit high frequencies. As the panels were...
Sorry Bernard for my very late ansver. No sorry I have not made any experience with "op amps built with discrete components".
I do not know if I mentioned that I swapped the 24 legged "oversampling" IC with a NOS-Board (non oversampling board) build with descrete components and with a higher...
While I am at it, I got a hint from a my high-end dealer telling me not to confection my Kimber 12TC as stated in my last thread above but like this:
For the panels - 2 conductors on the plus binding post and 6 conductors on the minus post (currently confectioned: 4 conductors per binding post...
I eventually decided to try out the Kimber 12CT (white/clear) each 1,5 meter per chanel in bi-amping confectioned like stated above 2x4 conductors for the panels and 2x8 conductors for the woofer. Imus say I do absolutely not regret the decision. Compared to my 35 year old Audio Note twisted...
Hi everybody,
First of all I want to wish you all a happy and healthy new year 2017 and lots of good :music:
Secondly I am a bit surprised that no one has an opinion to this thread. I do know its old and "dusty" but I cannot imagine that no one has tried the tweak and either made good or bad...